The Folly New Homes, Hornsea
Ward Homes Yorkshire used three Vandersanden coated bricks across 60 homes on the exposed Holderness coast, where wind, salt and frost test every facade.
For most of Hornsea’s past, the bricks tough enough for the sea air were the ones you’d rather hide round the back. At The Folly, Ward Homes Yorkshire didn’t have to make that choice.
Brick performance put to the test
Hornsea has been testing the performance of brick for generations.
About a mile from the development stands Bettison’s Folly, a 55-foot brick tower built around 1844 by local brewer William Bettison. Its builders used treacle bricks, over-fired bricks that became exceptionally hard but distorted during firing. Their appearance was secondary to their durability: on the exposed Holderness coast, the priority was simply finding a brick capable of withstanding the conditions.
Today's answer: coated bricks built to last
Almost two centuries later, housebuilders are asking many of the same questions. The difference is that modern manufacturing, allows us to create coated bricks, meaning durability no longer needs to dictate aesthetics in the same way.
Ward Homes Yorkshire named its largest scheme to date after Bettison’s tower. Sixty energy-efficient homes off Atwick Road, eight house types, in a town where the sea is a fifteen-minute walk and there is nothing between the facade and Denmark.
What weathers a brick facade on the UK's east coast?
There’s an assumption that coastal durability is about rainfall.
On this coast it isn’t. East Yorkshire is one of the driest parts of England. Hornsea sits in the rain shadow and receives roughly 600mm a year, against around 1,500mm on the Pennine tops.
What makes this site demanding are three other things.
Wind-driven rain. What matters to a wall is not how much rain falls but how hard it arrives horizontally. The Holderness plain is flat, the site is on the edge of town, and the fetch to the east is open North Sea.
Salt and efflorescence. Marine aerosol carries chlorides inland. Soluble salts move through a saturated brick, crystallise as it dries, and do two things: they mark the face, and over enough cycles the crystallisation pressure works on the pore structure itself.
Freeze-thaw. The two combine here. A brick that is repeatedly saturated by wind-driven rain and then frozen is a brick under pressure. East-coast winters deliver both, often in the same week. This is the failure mode that decides whether a facade at Hornsea looks the same in year twenty as it did in year one.
For a housebuilder, these conditions show why facing bricks need to be considered as both an architectural and a performance specification.
Distinctive character, lasting results built to withstand the weather
The choice of Vandersanden’s Bivio, Corum and Maltings bricks, featuring coated brick technology, delivered both the visual character and long-term performance the Ward Homes team was looking for at The Folly.
All three are multi bricks, mixing several tones within each brick. Bivio was chosen for its distinctive contemporary appearance, blending soft grey tones with subtle beige hues. Corum introduces yellow tones with grey across selected house types, while Maltings combines red, purple, black and beige hues to add depth, texture and variation throughout the scheme.
The result is a neighbourhood rich in visual interest, showing how coated bricks allow housebuilders to pursue the aesthetic ambition of a development while specifying for the practical demands of its location.
Charles Ward, Managing Director, Ward Homes explains how weather-resistant brick was specified
Taking all three from one range meant they shared a production method and a texture, so the street reads as one place rather than three decisions.
Sixty homes, eight house types, three different bricks. How do you prepare?
We set the rules before we set a brick. Bivio, Corum and Maltings aren’t distributed randomly, each one is tied to a house type and a position in the street scene, so the variation follows the massing rather than fighting it. Grey, buff and red is a wide range on paper.
You could have taken the best grey from one manufacturer, the best buff from another. Why all three from Vandersanden?
Because three bricks from three makers are three different risks. They’d have arrived on different lead times, weathered at slightly different rates, and if one went short mid-programme I’d have been matching a discontinued blend across a street that was already half built. Taking all three from one range meant they shared a production method and a texture, so the street reads as one place rather than three decisions. It also meant one conversation when I needed something, instead of three.
You’ve said supply reliability mattered. What had gone wrong before?
We’ve had projects where a brick went on extended lead time mid-build and we were left choosing between holding plots open or substituting. Either one costs you. On a development of this size, running three brick types across sixty plots, a single interruption doesn’t delay one house, it stalls a sequence. Thankfully, we did not have to deal with those issues on this project, or when working with Vandersanden.
What was the main driver of the design decision? Aesthetics or technical choices?
Both, and they pointed the same way. A projecting course on a west or east elevation here is a horizontal surface collecting water and a place for staining to start. The clean, flush approach was what we wanted the architecture to do anyway, and it’s also the more robust detail in this exposure. We didn’t have to choose.
One winter in: how the bricks stood up to the weather
The Folly represents Ward Homes Yorkshire’s largest scheme to date, delivered to create a diverse and distinctive community that caters to the local demographic while maintaining a consistent architectural identity throughout the development.
The homes came through winter 2025/26, a season in which England recorded around 35% above-average rainfall. No gypsum efflorescence was observed across the completed plots at the March 2026 inspection.
Project information
- Project – The Folly
- Homes – 60, eight house types, one to four bedrooms
- Location – Atwick Road, Hornsea, East Yorkshire
- Architect – Sangwin Architects
- Developer – Ward Homes Yorkshire
- Contractor – Ward Homes Yorkshire
- Merchant/Distributor – MKM Homes
- Bricks used – Bivio, Corum, Maltings
- Year of completion – 2026